WATERBURY FARRELL 010-012 mekanisk presse
Gallen
Hvis du beslutter at købe udstyret til en lav pris, skal du sikre, at du kommunikerer med den rette sælger. Find ud af så mange oplysninger som muligt om udstyrets sælger. En måde til at snyde på, er at lade som om, du er en reel virksomhed. Hvis der opstår mistanke, skal du informere os for en yderligere kontrol ved brug af formularen til feedback.
Før du beslutter dig til at købe, skal du undersøge adskillige salgstilbud grundigt for at opnå en forståelse af den gennemsnitlige pris på dit valgte udstyr. Hvis prisen på det tilbud, du kan lide, er meget lavere end lignende tilbud, skal du tænke dig godt om. En betydelig prisforskel er muligvis tegn på skjulte defekter eller et forsøg fra sælgerens side på at svindle eventuelle købere.
Køb ikke produkter med en for lav pris i forhold til den gennemsnitlige pris for lignende udstyr.
Stol ikke på tvivlsomme løfter og forudbetalte varer. Hvis du er i tvivl, skal du ikke være bange for at bede om yderligere oplysninger. Bed om flere fotografier og dokumenter for udstyret. Kontrollér, at dokumenterne er ægte. Stil spørgsmål.
Den mest almindelige form for svindel. Uhæderlige sælgere beder eventuelt om en forskudsbetaling for at "booke" din ret til at købe udstyret. Svindlere kan således indsamle et stort beløb og forsvinde, og ikke længere kontakte dig.
- Overførsel af forudbetalingen til kortet
- Foretag ikke nogen forskudsbetaling uden dokumenter, som bekræfter pengeoverførslen, hvis sælgeren er i tvivl i løbet af forhandlingerne.
- Overførsel til mellemmandens konto
- Du skal være på vagt over for en sådan anmodning, da du højst sandsynligt har at gøre med en svindler.
- Overførsel til en firmakonto med et lignende navn
- Vær opmærksom på, at svindlere muligvis udgiver sig for at være velkendte virksomheder ved at ændre navnet en lille smule. Overfør ikke penge, hvis der er tvivl om firmanavnet.
- Erstatning af egne oplysninger på en faktura fra en reel virksomhed.
- Før du foretager en overførsel, skal du sikre, at de specificerede oplysninger er korrekte, og om de har forbindelse til den specificerede virksomhed.
Sælgerens kontaktoplysninger
+34 937 64 ...
Vis
+34 937 64 96 80
Schweiz 
Schweiz, Gallen
Schweiz, Gallen
Schweiz, Gallen
Schweiz, Gallen
Schweiz, Gallen
Schweiz, Gallen
Schweiz, Gallen
Schweiz, Gallen
Schweiz, Gallen
Schweiz, Gallen
Schweiz, Brugg
Schweiz, Brugg
Belgien, Deinze
Tyskland, Bühl-Weitenung
Belgien, Deinze
Belgien, Deinze
Rumænien
Tyskland, Eislingen
Spanien, Barcelona
Nederlandene, Babberich
* Most Everything Refurbished! We can do more if you want more done.
* Plungers and Caps Scrapped back into Perfection
* Roller Boxes disassembled, Cleaned and Parts Replaced as necessary
* All new fasteners
* New oil lines, oil meters - Bijur. Anything left original was newer, tested and worthy of staying.
* 12 Plus 1 Stations - 12+1 or 12 plus Auxiliary Station (depends on your language)
* All new Felt Plunger Wipers and Aluminum plates to hold it in place
* Bronze Slide / Bed Inserts. Bronze Transfer Ways
* Minster Combo Clutch and Brake - Air power
* Lift Rod Frictions on top of press - new style and easy to change / check
* 12 Bottom Cams - WOW - full set
* Currently set up with US Motors 3 Hp mechanical vary drive system - old working junk. I would switch to AC Inverter and we can do it for a price. Just being honest.
* 1.125" tall die holders x 2.5" transfer - center distance
* 12 Kick up Plunger Friction Assemblies - new hardware
* 2" total Stroke of Ram Plungers - a little short for a 1012 but this is a speedy accurate press for parts under .90" tall..
* Serial No. ST237383 55 237975
* Press has flywheel cover not shown. Off during refurbishment.
* Ross duel safety solenoid valve - old but working.
* Waterbury spring loaded fork elevator type strippers (off press for rebuild now).
* Clutch is good and we have not disassembled it or refurbished it.
* Controls are 1980 vintage. Working but just ok.
We could rebuild the clutch - New O-Rings, Seals, Springs, Rotary Union, check friction material, literally put most of it in a dip tank and clean it all up. Paint. Could reline if pads are worn or replace. Service whole clutch professionally so it is good for another 10 years. Would charge $500 to disassemble and diagnose and then quote any parts or labor it needs.
Electrical - Can replace all the electrical to your specs or do it like all the other eyelet guys around here do it. Would quote but probably $10k for new controls. Those guys think think they are NYC Lawyers.
This press was built as a higher speed 1012 model. The pressing cams are the faster speed type and bolted together for a solid top shaft set up. The plungers don't have keys and goose rods so they won't come out of adjustment at speed. The roller boxes don't go up and down and therefore make less noise and are more accurate.
Press could be demonstrated on our shop floor. Come look at it. Excellent specimen.
Price listed is for a finished refurb as described - will finish the plunger install. Will paint press when done. Does not include clutch work, controls work or any added parts. Press will be running with existing controls and systems unless buyer wants other work done.
Waterbury Farrel 1012 ICOP Transfer Press Refurbished w Minster Clutch Mint!
* Most Everything Refurbished! We can do more if you want more done.
* Plungers and Caps Scrapped back into Perfection
* Roller Boxes disassembled, Cleaned and Parts Replaced as necessary
* All new fasteners
* New oil lines, oil meters - Bijur. Anything left original was newer, tested and worthy of staying.
* 12 Plus 1 Stations - 12+1 or 12 plus Auxiliary Station (depends on your language)
* All new Felt Plunger Wipers and Aluminum plates to hold it in place
* Bronze Slide / Bed Inserts. Bronze Transfer Ways
* Minster Combo Clutch and Brake - Air power
* Lift Rod Frictions on top of press - new style and easy to change / check
* 12 Bottom Cams - WOW - full set
* Currently set up with US Motors 3 Hp mechanical vary drive system - old working junk. I would switch to AC Inverter and we can do it for a price. Just being honest.
* 1.125" tall die holders x 2.5" transfer - center distance
* 12 Kick up Plunger Friction Assemblies - new hardware
* 2" total Stroke of Ram Plungers - a little short for a 1012 but this is a speedy accurate press for parts under .90" tall..
* Serial No. ST237383 55 237975
* Press has flywheel cover not shown. Off during refurbishment.
* Ross duel safety solenoid valve - old but working.
* Waterbury spring loaded fork elevator type strippers (off press for rebuild now).
* Clutch is good and we have not disassembled it or refurbished it.
* Controls are 1980 vintage. Working but just ok.
We could rebuild the clutch - New O-Rings, Seals, Springs, Rotary Union, check friction material, literally put most of it in a dip tank and clean it all up. Paint. Could reline if pads are worn or replace. Service whole clutch professionally so it is good for another 10 years. Would charge $500 to disassemble and diagnose and then quote any parts or labor it needs.
Electrical - Can replace all the electrical to your specs or do it like all the other eyelet guys around here do it. Would quote but probably $10k for new controls. Those guys think think they are NYC Lawyers.
This press was built as a higher speed 1012 model. The pressing cams are the faster speed type and bolted together for a solid top shaft set up. The plungers don't have keys and goose rods so they won't come out of adjustment at speed. The roller boxes don't go up and down and therefore make less noise and are more accurate.
Press could be demonstrated on our shop floor. Come look at it. Excellent specimen.
Price listed is for a finished refurb as described - will finish the plunger install. Will paint press when done. Does not include clutch work, controls work or any added parts. Press will be running with existing controls and systems unless buyer wants other work done.